FREE SHIPPING ON ORDERS OVER $25

Installation Instructions

P/N 9900 (red filter) P/N 9900B (blue filter) P/N 9900K (black filter) P/N 9900W (white filter)
(Click to see a hi-res version of the image)

Year/Make/Model/Engine

02-06 Cadillac Escalade 5.3L V8

02-06 Cadillac Escalade 6.0L V8

02-06 Cadillac Escalade EXT 6.0L V8

03-06 Cadillac Escalade ESV 6.0L V8

02-06 Chevy Avalanche 5.3L V8

99-06 Chevy Silverado/GMC Sierra 1500 4.8L V8

2007 Chevy Silverado/GMC Sierra 1500 Classic 4.8L V8

99-06 Chevy Silverado/GMC Sierra 1500 5.3L V8

2007 Chevy Silverado/GMC Sierra 1500 Classic 5.3L V8

2007 Chevy Silverado/GMC Sierra 1500 Classic 6.0L V8

01-05 Chevy Silverado/GMC Sierra 1500HD 6.0L V8

2007 Chevy Silverado/GMC Sierra 1500 HD Classic 6.0L

V8 99-06 Chevy Silverado/GMC Sierra 2500 5.3L V8

99-06 Chevy Silverado/GMC Sierra 2500 6.0L V8

01-05 Chevy Silverado/GMC Sierra 2500HD 6.0L V8

2007 Chevy Silverado/GMC Sierra 2500 HD Classic 6.0L V8

03-06 Chevy Silverado SS 6.0L V8

2007 Chevy Silverado SS Classic 6.0L V8

00-06 Chevy Tahoe/GMC Yukon 4.8L V8

00-06 Chevy Tahoe/ Chevy Suburban 5.3L V8

00-06 GMC Yukon/GMC Yukon XL 5.3L V8

00-06 Chevy Tahoe/ Chevy Suburban 6.0L V8

01-04 GMC Yukon Denali 6.0L V8

Parts List:

1- Filter shield
1- Air filter
1- Intake tube
1- MAF sensor adapter
1- Rubber vibration mount
2- M6 fender washers
2- M6 locknuts
1- 4” coupler
1- 4” coupler 90°
4- 4” hose clamps
1- 6” hose clamp
1- MAF adapter ring
3- M5 allen bolts
3- M5 flat washers
3- M5 lock nuts

Tools Required:

• 10mm socket or wrench

• 5/16” nut driver or flat blade screwdriver

• 5/32 Allen wrench

• 5/16” wrench

For filter reorders ask at the special order counter of your local parts store or call 1-909-673-9800 and ask for:

  • P/N HPR9891(red filter)
  • P/N HPR9891B (blue filter)
  • P/N HPR9891K (black filter)
  • P/N HPR9891W (white filter)

Step 1

Safety First! Before you begin, disconnect the negative terminal on your battery. Verify all components listed are present before beginning your installation.

Step 2

Start by loosening the clamps securing the OE intake tube to the throttle body and the MAF sensor.

Step 3

Remove the OE intake assembly out of the engine.

Step 4

Disconnect the MAF sensor.

Step 5

Grab the air box from both sides and pull up and out. The air box is held in place with rubber grommets.

Step 6

Loosen the hose clamp securing MAF sensor to the air box. Carefully remove MAF sensor and rubber ring from the air box assembly and set aside for later use.

Step 7

Remove the five 10mm bolts securing the lower air box tray and remove tray. Set the bolts aside as they will be reused later.

Step 8

Using the included 5mm Allen bolts, lock nuts and washers, assemble the heat shield as shown. Install the Allen bolts from the outside of the shield and put the flat washer and lock nuts on the inside. Once all the hardware is installed, use the included hex key wrench and an 8mm (5/16” will also work) wrench to fully tighten all of the lock nuts. Place the filter shield in the engine compartment. Secure the shield with the air box tray bolts removed in step 7.

Step 9

Place the rubber vibration mount, fender washers and M6 lock nuts on the side of the housing as shown. Do not tighten the bolts at this time.

Step 10

Slide the 4” angled coupler and two 4” hose clamps over the throttle body. Do not tighten the clamps at this time.

Step 11

Place the intake tube in the engine compartment. Slide the lower angled bracket between the vibration mount and the housing.

Step 12

Insert the radiator hose bracket into the bracket on the side of the intake tube.

Step 13

Install the adapter ring onto the MAF as shown. Install the 4” coupler over the adapter ring and secure with the supplied hose clamp.

Step 14

Attach the MAF sensor and OE rubber ring to the MAF adapter. Slide the adapter between the rubber ring and the tabs as shown. Secure MAF sensor to the adapter with the OE hose clamp.

Step 15

Carefully insert the air filter over MAF sensor assembly and secure with the provided hose clamps.

Step 16

Insert the supplied hose clamp over the 4” boot. Install the air filter assembly onto the intake tube. Position the MAF so that the connector points to the wiring harness. Connect the assembly to the intake tube.

Step 17

Secure the vibration mount and tighten all the hose clamps. Do not over tighten. Reconnect the MAF sensor wiring connector.

Step 18

Gently close the hood and check to make sure the intake assembly does not come in contact with the hood when closed. Make any adjustments if necessary.

Step 19

Make sure all bolts and clamps are now tight. Reconnect the negative terminal on the battery. Start up the engine and check for any air leaks. Affix the CARB. E.O. sticker in a prominent place under the hood.Your installation is now complete. Periodically check all clamps and brackets. Enjoy your Spectre Intake System.

If you have any difficulties or questions regarding the installation of this intake system, contact the Spectre Performance Technical Department by email - Tech@spectreperformance.com or by phone 1-909-673-9800 Monday thru Friday 6:00am to 2:00pm PST.

176153A
1/27/16